WEAVER - Catalogue 2021

1. Shimming is probably required for perfect scope alignment.  2. Rear base may require modifications for correct fit to military actions.  3. Front base may require modification for correct fit.  4. Gun will have to be drilled and tapped.  5. Front base screws must be shortened by grinding.  6. May require bolt and/or safety alteration, otherwise firearm cannot function safely and prop- erly. Consult with a qualified gunsmith.  7. BASE DOES NOT FIT ROSSI LARGE FRAME MATCHED PAIR COMBOS (ALL MODELS WITH 20 OR 12 GA SHOTGUN BARRELS).  8. Remove rear sight to use.  9. The handiest way to pinpoint the correct base for the Win. 52 & Win. 70 Long Action Rifles is to check the spacing of the tapped holes for the rear base and compare it to the hole spacing for the front base. Does it have: HOLE SPACING THE SAME HOLE SPACING IS DIFFERENT Model 52 Use 46+ 46 Model 52 Use 25+ 57 Model 70 Use 47+ 46 Model 70 Use 49A+ 46 10. The Weaver type base built into this rifle will accept Weaver rings, but our highest ring (1" See-Thru #49513) still isn’t high enough to clear the front sight. 11. The Weaver type base built into this firearm will accept any Detachable Top Mount Weaver Ring. 12. Rifle has Grooved Receiver for Tip-Off Rings. 13. Ruger Mark II Pistols. Weaver only offers a clamp on base with 1" rings (Pistol Mount System #306). Ruger supplies a short or long base and 1" or 30mm rings w/factory drilled and tapped pistols. Contact Ruger for these items. 14. Bolt clearance problem may exist and scope will not be centered. 15. Base accepts Tip-Off Rings only. 16. TO-9, TO-10 & TO-11 bases accept either Detachable Top Mount Rings or Tip-Off Rings. Each have crossbolt slots and 3/8" grooves for both applications. 17. Must be factory drilled and tapped. 18. One-Piece base attaches to barrel and extends back over receiver. 19. Requires the use of Thompson/Center base adapter. 20. Requires drilling and tapping 4 holes in receiver and relief space cut in stock to clear base. 21. Rear base is positioned on top of receiver and front base is positioned on the barrel. Drilling & tapping required. One-piece base mounts with 2 set screws & newer guns are factory drilled & tapped. 22. For shorter tube scopes or red dot scopes use #402 extension front base or one-piece base if available. Extension base allows an extra .689". 23. WARNING: NOT FOR USE WITH X-FRAME REVOLVERS. USE ON FIREARMS OTHER THAN THOSE LISTED MAY CAUSE INJURY. 24. Top mount base is designed to fit 12GA models only. 25. Can be used with Tactical Multi-Slot Base. 26. Rear base screws must be shortened by grinding. 27. Tactical Extended Multi-Slot Bases have 20 MOA versions as well. See product information section on page 13 for details. 28. This mount will not work on Ruger Blackhawk pistols with a flattop receiver. To find the correct base or mount to fit your firearm, you need to know the product number. To do this, follow these steps: 1. In the firearm column, find the manufacturer and make/model of your firearm (for example, Browning A-Bolt). 2. Next, find the 5-digit Product Number (for example: 48955), in the desired Product Category column (for example, Grand Slam Dovetail Bases). NOTE: in some cases, you will find a short reference number (for example, 60A) listed in the chart. Use this reference number to find the appropriate Product Number. 3. Product Numbers are found near the appropriate product description sections placed throughout the catalog. If necessary, match the reference numbers to product numbers. Notes: Ring Size Saddle Height Fits Objective 1" Low 0.150 Up to 40mm 1" Medium 0.270 Thru 50mm 1" High 0.400 Thru 56mm 1" X-High 0.520 Over 56mm 30mm Medium 0.320 Thru 56mm 30mm High 0.490 Over 56mm 1" Medium .22 Rings 0.262 Thru 40mm 1" High .22 Rings 0.392 Thru 44mm 1" X-High .22 Rings 0.512 Thru 50mm 1" Medium Mod 77/22 & No 1 0.453 Thru 50mm 1" Medium Mod 77 Stepped Thru 50mm 1' High Mod 77 Stepped Thru 56mm Note: Chart applies to Dovetail Rings. Ring Size Saddle Height Fits Objective 1" Low 0.089 Thru 38mm 1" Medium 0.169 Thru 40mm 1" High 0.332 Thru 44mm 1" X-High 0.560 Thru 50mm 1" See-Thru 0.750 Thru 50mm 30mm Low 0.288 Thru 33mm 30mm High 0.500 Thru 44mm 1" Tip-Off 0.250 Thru 36mm 1" Tip-Off See-Thru 0.750 Thru 50mm Note: Chart applies to Grand Slam, Sure Grip, Detachable, Quad Lock and Lever Lok Rings. Ring Size Saddle Height Fits Objective 1" Med .280" Thru 40mm 1" High .400" Thru 44mm 1" X-High .520" Thru 50mm 1" XX-High .640" Thru 56mm 30MM Low .250" Thru 38mm 30MM Med .370" Thru 40mm Top Mount Ring Height Guide Dovetail Ring Height Guide Tactical Style Ring Height Guide Ring Size Saddle Height Fits Objective 30MM High .490" Thru 44mm 30MM X-High .610" Thru 56mm 34MM Low 0.327 Thru 24mm 34MM High .0.577" Thru 44mm 34MM XX-High 0.827" Thru 56mm MOUNTS CHART THIS NOTES SECTION IS ALSO ON THE INSIDE BACK COVER FOR QUICK REFERENCE

RkJQdWJsaXNoZXIy NTY3Nzg=